Home > LED Drivers > Constant Current >

PTB30W-0700-42-FN ERP Constant Current LED Driver

ERP PTB30W-0700-42-FN constant current led driver wire leads LED Lighting


 
Alternative Views:


$8 Flat Rate Ground Shipping!

Download Data Sheet

Our Price: $38.00


Availability:: In Stock
Product Code: PTB30W-0700-42-FN

Description Certifications Mechanical Details
 

30 W Programmable CC Class 2 LED Driver with Enhanced Tri-Mode Dimming (TRIAC, ELV & 0-10 V)
Technical Data

2 - INPUT SPECIFICATION (@25°C ambient temperature)

Units

Minimum

Typical

Maximum

Notes

Input Voltage Range (Vin)

Vac

90

120, 277

305

Ÿ The rated output current for each model is achieved at Vin108 Vac & at Vin249 Vac.

Ÿ At nominal load

Input Frequency Range

Hz

47

50/60

63

Input Current (Iin)

A

0.32 A @ 120 Vac

0.15 A @ 277 Vac

Power Factor (PF)

0.9

> 0.9

Ÿ At nominal input voltage (120 & 277 Vac)

Ÿ From 100% to 60% of rated power

Inrush Current

A

Meets NEMA-410 requirements

Ÿ At any point on the sine wave and 25°C

Ÿ Active limiting inrush current is available as an option. Please contact your ERP representative or send an email to [email protected].

Leakage Current

mA

0.3 mA @ 120 Vac

0.7 mA @ 277 Vac

Measured per IEC60950-1

Input Harmonics

Complies with IEC61000-3-2 for Class C equipment

Total Harmonics Distortion (THD)

20%

Ÿ At nominal input voltage (120 & 277 Vac)

Ÿ From 100% to 60% of rated power

Ÿ Complies with DLC (Design Light Consortium) technical requirements

Efficiency

%

-

up to 90%

-

Measured with nominal input voltage, a full sinusoidal wave form and without dimmer attached.

Isolation

The AC input is isolated from the main DC output.

3 - MAIN OUTPUT SPECIFICATION (@25°C ambient temperature)

Units

Minimum

Typical

Maximum

Notes

Output Voltage (Vout)

Vdc

See ordering information for details

Output Current (Iout)

mA

Ÿ See ordering information for details

Ÿ The rated output current for each model is achieved at Vin108 Vac & at Vin249 Vac.

Output Current Regulation

%

-5

±2.5

5

Ÿ At nominal input voltage (120 & 277 Vac)

Ÿ Includes load and current set point variations

Output Current Overshoot

%

-

-

10

The driver does not operate outside of the regulation requirements for more than 500 ms during power on with nominal LED load and without dimmer.

Ripple Current

20% of rated output current for each model

Ÿ Measured at nominal LED voltage and nominal input voltage without dimming

Ÿ Calculated in accordance with the IES Lighting Handbook, 9th edition

Ÿ Meets IEEE 1789-2015 "no impact" recommended practices for flicker

Dimming Range (% of Iout)

%

1

100

Ÿ The dimming range is dependent on each specific dimmer. It may not be able to achieve 1% dimming with some dimmers.

Ÿ Dimming performance is optimal when the driver is operated at its nominal output voltage matching the LED nominal Vf (forward voltage). Dimming performance may vary when the driver is operated near its minimum output voltage.

Start-up Time

ms

300

500

Ÿ Without any dimmer attached, and at nominal input voltages and nominal load

Ÿ Measured from application of AC line voltage to continuous light output. 100% light output achieved 750 ms.

Ÿ Complies with ENERGY STAR® luminaire specification and CA Title 24

Isolation

The main DC output is certified and tested per UL8750 Class 2 or LED Class 2. In models without a suffix and

"-Z1" models, the 0-10 V dimming circuit is isolated from the AC input and the DC output



4 - 0-10 V DIMMING CONTROL (@25°C ambient temperature)

In the PTB30 series, several 0-10 V dimming profiles can be selected, such as a logarithmic profile, a non-linear profile with 1% minimum dimming, and a non-linear profile with 10% minimum dimming. Additionally, models with the “-Z1” suffix can utilize a non-linear profile with 1% minimum dimming with dim-to-off and a non-linear profile with 10% minimum dimming and dim-to-off. Furthermore, every point in the non-linear dimming profile can be programmed using the programming software.


By default, the non-linear profile with 1% minimum dimming (shown in figure 1) is pre-loaded in the PTB30 series. Models with the “-Z1” suffix are pre-loaded with the non-linear profile with 1% dimming and dim-to-off (shown in figure 2).



9 - PHASE-CUT DIMMING

Dimming of the driver is possible with standard TRIAC-based incandescent dimmers that chop the AC voltage as shown in Figure 3, or with ELV dimmers. During the rapid rise time of the AC voltage when the dimmer turns on, the driver does not generate any voltage or current oscillations, and inrush current is controlled. During the on- time of the AC input, the driver regulates the output current based upon the conduction angle. The RMS value of the driver output current is proportional to the on-time of the AC input voltage. When operating with an incandescent dimmer, the RMS output current varies depending upon the conduction angle and RMS value of the applied AC input voltage.

Forward-phase (TRIAC) and reverse-phase (ELV) dimming work only at 120 Vac.

The PTB30 series offers Tri-Mode Dimming™ compatibility with both phase-cut (reverse-phase and forward- phase) and 0–10V dimmers. Phase-cut dimming always has priority over 0-10 V dimming.

10 - COMPATIBLE PHASE-CUT DIMMERS

120Vac Dimmers

Mfg.

Model

Mfg.

Model

Mfg.

Model

Lutron

LGCL-153PL

Lutron

DVRP-253P

Leviton

VPE06

Lutron

RRD-6CL

Lutron

NTELV-600P

Leviton

DW1KD-1BZ

Lutron

DVELV-303P

Lutron

MAELV-600

Cooper

SAL06P-W-K

Lutron

MACL-153M

Lutron

SCL-153P

Cooper

DAL06P

Lutron

RRD-10ND

Leviton

DSL06-1LZ

Cooper

TAL06P1-C1

Lutron

PD-6WCL

Leviton

IPE04

Lutron

SELV-300P

Leviton

IPL06

Lutron

DVCL-153P

Leviton

6674


Share your knowledge of this product. Be the first to write a review »